Just how do you feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't specifically rocket science, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the job can relocate immediately; if you have to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is much better to think about utilizing one before you begin. Chances are you might require a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently gotten a new bathtub and also do not need to change the setup of your previous water pipelines.
Your tools and product list ought to comprise the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's instruction manual. Tiling and securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to problems with moisture and also feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Remember to always fill the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof adhesive and grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you enjoyed our article about Installing A Bathtub. Thanks a lot for taking a few minutes to browse our article. If you please take the opportunity to share this blog if you enjoyed reading it. Kudos for your time. Please stop by our website back soon.
Free Estimates